Technical Specification
Model |
900 VA |
1100 VA |
1600 VA |
2100 VA |
Nominal Battery Voltage |
12 VDC |
24 VDC |
Solar Panel Connected for 50Amps PWM Charge Controller (Max.) |
850 Wp |
850 Wp |
1700 Wp |
1700 Wp |
AC Mains Mode
Input Voltage Range (Normal Mode) |
100 to 290 VAC ± 5 VAC (Wide Range) |
Input Voltage Range (UPS Mode) |
180 to 260 VAC ± 5 VAC |
Changeover Time Maximum |
< 30 ms (in Normal Mode) and < 10 ms (in UPS Mode) |
Max. Charging Current |
5A to 18A ± 1A (User Programmable) |
Boost Charging Voltage |
14 VDC to 15 VDC ± 0.2 VDC per Battery (User Programmable) |
Boost Charging Voltage (Factory Default) |
14.4 ± 0.2 VDC for Tubular 13.8 ± 0.2 VDC for SMF |
28.8 ± 0.4 VDC for Tubular 27.6 ± 0.2 VDC for SMF |
Float Charging Voltage (Factory Default) |
13.7 ± 0.2 VDC for Tubular 13.5 ± 0.2 VDC for SMF |
27.4 ± 0.4 VDC for Tubular 27.0 ± 0.2 VDC for SMF |
Battery Backup Mode
Output Voltage at No Load |
220 VAC ± 7 VAC |
Output Frequency |
50.0Hz ± 0.5Hz |
Output Wave Form (At No Load) |
100% Pure Sine Wave |
Battery Low Alarm |
10.6 ± 0.2 VDC |
21.2 ± 0.2 VDC |
Battery Low Protection |
10.4 ± 0.2 VDC |
20.8 ± 0.2 VDC |
Overload (Normal/UPS) |
120% (30 Sec) |
Short Circuit (Normal/UPS) |
300% |
CHARGING MODE
Max. Charging Current |
5A to 30Amp. ± 1.5Amp. (User Programmable) |
Charge Controller Efficiency |
> 98% |
DESCRIPTION OF SWITCHES ON FRONT PANEL
S.No. |
Switch |
Function(s) |
Switch Led Status |
1 |
POWER |
ON/OFF the UPS Output |
System ON - Led ON System OFF - Led ON |
2 |
INV/UPS |
When it is Short Pressed it Enables UPS/Inverter Mode Selection
When it is Long Pressed Enables the UPS Parameter Setting :
The LCD Displays : “Edit Parameters Setting”
The Switches function now Change to :
POWER - Enter/OK Switch
INV/UPS - Increment Value
SMF/TUB - Decrement Value
HYBRID/PCU - Back/Exit Switch |
UPS Mode ON - Led ON UPS Mode OFF - Led OFF |
3 |
SMF/TUB |
When it is Short Pressed it Enables TUBULAR or SMF Battery Selection |
System ON - Led ON System OFF - Led ON |
4 |
HYBRID/PCU |
When it Short Pressed it Enables the Hybrid PCU Mode Selection |
PCU Mode - Led ON Hybrid Mode - Led OFF |
DESCRIPTION OF CENTER LED ON FRONT PANEL
S.No. |
LED |
Description |
1 |
GREEN |
LED ON - Full Solar Used LED Blinking - Partial Solar Used LED OFF - No Solar Used |
2 |
RED |
LED ON - PV Reverse Protection LED OFF - No Protection Selected |
Note:for expert we can provide 25Ah & 55Ah also.
CONVENIENCE
Solar Hybrid DSP uses both Solar Power as well as Mains for charging the battery bank according to parameter priority set, providing the users availability of uninterrupted power supply.
- Smart Load sharing compatibility.
- Inbuilt Solar Charge Controller with high charging Current
- Three stage solar charging (TSSC), suitable for all type of battery charging .
- PV availability, battery charging from solar power indication with display on LCD.
- Deep discharge battery charging from mains as well as solar .
- Battery type charging selection (Tubular /Flat /SMF/GEL )
- Duel Modes of operation ( EC/NC) Solar + Mains Charging Current Adding in NC Mode , Max charging current at below 13.7 V Battery voltage, > 13.7 charging current is 15A ± 1A.s
- Smart grid charging option with Enable/Disable option.
- User selectable UPS and Normal Mode.
- Resettable AC circuit breaker which reduce service calls.
- Generator compatible.
- Protections against short-circuit ,Mains Fuse Trip , Overload, reverse phase, low battery, reverse battery and over temperature (With proper indications with buzzer as well as display on LCD available).
- User friendly, feather touch control and selection switches with LED indication on front panel.
- Battery charging even at low voltage.
- Comprehensive LCD Display
- Operate on both Solar Power as well as Grid Power
- It is Integrated with in-built fully regulated 50Amp PWM Solar Charge Controller for maximum Solar Power Utilization
- Upgradable on 70Amp PWM Solar Charge Controller
- It senses the availability of Solar power, Grid power and accordingly gives preference to charging through solar power and switches to the grid power is not available
- It is designed to give you maximum benefit from the solar energy and minimize your electricity bill drastically
- Highly efficient battery charging from the solar energy as a result you will get non-stop power, save money, save electricity, and protect the environment
- Advanced DSP technology for absolute and stable and 100% pure sine wave output
- Indications for Mains ON, UPS ON, Battery Low, Charging/Discharging, Over Load, Short Circuit, Thermal Trip, Solar available/Not available and PV reverse on LCD Display
- User-Friendly LCD for the display of mode of operation and all parameters
- DUAL MODE OF WORKING : UPS AND NORMAL
- DUAL SOLAR MODE : HYBRID AND PCU MODE
- DUAL BATTERY CHARGING MODE : TUBULAR AND SMF BATTERY MODE
- Intelligent overload sensing circuitry with auto retries facility
- Programmable thermal protection : cooling fan which operates as needed
- High Power new generation MOSFET cable to handle high in-rush/ surge current
- Double stage MOSFET Over Current Protection by measuring Rds ON
- Highest efficiency at lower cost
- Pure Sine Wave Output with low Total Harmonic Distortion (THD)
- High End ARM-Cortex based design of Solar Charge Controller for charging through Solar Power
- Eco-friendly operation
- Solar PV reverse voltage protection
- Electronic Over Current Charging Protection
- Reverse Current Flow Protection from Battery to Solar Panel generally during night
- No mechanical contact for charge Controller
- Designed for continuous reliable and robust operation